EXACTLY HOW TO REPLACE A TUB IN YOUR BATHROOM

Exactly How to Replace a Tub in Your Bathroom

Exactly How to Replace a Tub in Your Bathroom

Blog Article

Schedule Service

We've uncovered this article pertaining to How to Install a Bathtub below on the net and think it made perfect sense to write about it with you on this page.


A Step-by-Step Guide to Installing a Bathtub
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old bathtub is conveniently obtainable, the job can relocate easily; if you have to open up a wall surface to remove the old tub and position the brand-new bath tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the brand-new one. Make certain you have qualified on your own for the work and also are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly assist you install a new bath tub in your shower room if you have actually already gotten a new bathtub and also do not require to transform the arrangement of your previous supply of water pipes.
Your tools and also product list ought to comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Planning for the Setup


    To start with, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to stop stress on the bathtub.
    Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final setting.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any water staying in the system. The process of eliminating the existing taps can be rather bothersome because of the limited gain access to that is usually the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
    Prior to going on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

    Setting up the Bath tub


    Using the two wooden boards under its feet, place the tub in the called for position. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
    The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the spirit level reads degree.
    To mount taps, fit the bottom of the furthest adaptable tap connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
    Activate the water and check all joints and new pipework for leaks and tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the regular electrical outlet for leakages.
    Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it into its final position.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
    If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the faucet ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bath tub


    In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing issues with wetness and feasible leaks to the ceiling listed below.
    You can select from a variety of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split rather early if you do not think about this motion prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the market. It is recommended to fit the floor tiles using water-resistant or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    As a passionate person who reads about How to Install a Bathtub, I assumed sharing that article post was essential. Enjoyed our write up? Please share it. Let other people discover it. Thanks so much for going through it.



    Services

    Report this page